dyno run

HIGGSPEED · Post by **HIGGSPEED** » Mon May 25, 2009 3:28 pm

Thats a coincidence Paul,

I am taking my h2c down to the dyno tomorrow. i will post my results also.Wiseco 1mm o/s and 34mm vm's with my pipes on
Cheers
Higgsy!

downpipe3 · Post by **downpipe3** » Mon May 25, 2009 5:34 pm

what time paul ?
i may be able to come up and see you and chris

gary c

Ståle · Post by **Ståle** » Mon May 25, 2009 10:09 pm

HIGGSPEED wrote:Thats a coincidence Paul,

I am taking my h2c down to the dyno tomorrow. i will post my results also.Wiseco 1mm o/s and 34mm vm's with my pipes on
Cheers
Higgsy!

79 HP.

Kawasaki

HIGGSPEED · Post by **HIGGSPEED** » Tue May 26, 2009 8:53 pm

Not far off Stale my little viking buddy!!

I have never been over impressed with my h2c, although it pulls well enough and suffers from no surge whatsoever,i always felt a bit disappointed when i rode it. I recently put a set of 34mm vm rounslides on (cheers Malc ) and still it didnt float my boat.
Today i took it to the dyno and sorted it properly. I wished i had done it ages ago but you know how it is .. so many other things to sort.
Anyway i digress

First run 68bhp but wildy lean at the bottom and mirange. Dropped the needles to the centre clip (they were on the top clip ie leanest position. Wahay 71 bhp but still real lean at the bottom. Swapped the pilots a few times and ended up with 45 pilots (was 35).
The final icing on the cake was to liberally oil the foam filters as it just started to wander slightly lean flat out.
SORTED
75 bhp at the back wheel and it wheelies in first , change to second and it wheelies again!! I was grinning all the way home

I have put the second graph in as it shows the air fuel better. I am well pleased with this a/f ratio as it is near perfect 13:1 all the way and just slightly dips rich at the tail end which is what you want.
You also learn a lot too, i have learnt that is a waste of time revving MY motor over 7 as it has peaked, although it will continue to rev, it will accelerate faster by changing up just short of 7.

Incidentally i should mention that i was running 230 mains originally to err on the side of caution which explains why i was unimpressed

200 mains was the final choice, 45 pilots and middle clip on the needle. Oh and 2 turns out on the airscrew. Ticks over very strong at 1500 rpm.

Top tip of the day......... oil them foam filters . You wont lose any midrange , but it acts as a bit of insurance at the top end as it restricts the absolute flat out in top flow and keeps your pistons in one piece.And it keeps more dust out of your engine.. bonus ball!

Higgsy

h2chris · Post by **h2chris** » Tue May 26, 2009 10:11 pm

Great post Dave,

Thanks for sharing.

Ståle · Post by **Ståle** » Tue May 26, 2009 10:18 pm

I have dry UNI's. What kind of oil should I use on them ?

downpipe3 · Post by **downpipe3** » Wed May 27, 2009 6:11 am

good post dave
the results from carbs set up being right are amazing and can transform a bike

you cant beat a dyno for set up

husson73 · Post by **husson73** » Wed May 27, 2009 9:23 am

Great power and post

SAM · Post by **SAM** » Wed May 27, 2009 9:33 am

MAKES YOU THINK!

HIGGSPEED · Post by **HIGGSPEED** » Wed May 27, 2009 12:50 pm

sorry for hi - jacking your post Paul

Thanks guys i am well pleased with it. Stale, i dont think it matters too much what oil you use, but a light oil in a sprayer works best.

Higgsy

HIGGSPEED · Post by **HIGGSPEED** » Wed May 27, 2009 12:51 pm

that should read LIGHT OIL

can't seem to edit my posts on this forum??

malc87 · Post by **malc87** » Wed May 27, 2009 1:18 pm

HIGGSPEED wrote:that should read LIGHT OIL
can't seem to edit my posts on this forum??

i think you only have a short time to edit your posts, unless you are a moderator.
i do correct genuine mistakes (as a mod) when i see them.

Ståle · Post by **Ståle** » Wed May 27, 2009 2:28 pm

Cheers Higgsy.

Malc, I just edited my 79HP post. No problem.

Post by **Wolfie** » Wed May 27, 2009 7:28 pm

Just what sort of moola we talking about for a day at the Dyno?

malc87 wrote:i do correct genuine mistakes (as a mod) when i see them.

Just occasionally mee too, done for you Higgsy.

but now that buggers up your second post...

HIGGSPEED · Post by **HIGGSPEED** » Wed May 27, 2009 8:28 pm

Mmm just hang fire for a while Wolfie, i am currently in negotiation for my own premises with in house dyno. I will elaborate on another thread in due course.

Cheers
Higgsy!

g6mow · Post by **g6mow** » Wed May 27, 2009 8:37 pm

Post by **Wolfie** » Wed May 27, 2009 10:37 pm

I was just being nosey Higgsy, I don't want to spend any money, I have a reputation to live up to you know...

the180kid · Post by **the180kid** » Tue Jun 02, 2009 9:54 am

Wolfie wrote:Just what sort of moola we talking about for a day at the Dyno?

malc87 wrote:i do correct genuine mistakes (as a mod) when i see them.
Just occasionally mee too, done for you Higgsy.

but now that buggers up your second post...

£48 round here, for a few hours to sort out air-fuel,..

TallyB · Post by **TallyB** » Tue Jun 02, 2009 1:38 pm

[Mmm just hang fire for a while Wolfie, i am currently in negotiation for my own premises with in house dyno.

That sounds like a mid-week break for me. Get the overnight boat from Larne to be in Blackpool in the morning to get the bike sorted.
late boat back again. Thats B+B sorted as well as the bike.

SAM · Post by **SAM** » Tue Jun 02, 2009 4:36 pm

Wolfie wrote:I was just being nosey Higgsy, I don't want to spend any money, I have a reputation to live up to you know...

We all know