Gary Clarke

[husson73]

have you still a set of cooper base gasket for H2?, need a set

http://kawaportal.org/phpBB2/viewtopic. ... ght=#60821

[downpipe3]

yes mr JP i have a new batch due in this week mon ami as soon as theyt arrive i will contact u

[husson73]

very good, how thin are they

[downpipe3]

same size as standard gasket JP
they are now back in stock do you want me to paypal invoice you ? thats the easiest way for me

[husson73]

Well, in fact won't used them cause that I need is a kind of big mettalic gasket cause my top crankcase has been elarging on the side ports and raise from 1 minimeter (bike could have done drag racing cause there is a drag race sticker on the tank: 71 H2 coming from USA via Rick)
Excepted this and a hole on the rear top case and a little broken part the cases are in VGC specially on the crankshaft bearings seats and want to use them as they matching with my H2F 0026* frame (not the same numbers of course but original one).
So the bike won't be at Spa and my 69 H1 will do the job with my other triples (some friends come with me).
Hope for the Southern this H2 will be ready.

[downpipe3]

jp i can get whatever thickness you require mon ami [within reason]
if you let me know what thickness you want i will see what i can do , i can have them made in aluminium if you want

[husson73]

jp i can get whatever thickness you require mon ami [within reason]
if you let me know what thickness you want i will see what i can do , i can have them made in aluminium if you want

oh yes I want, just have to know the exact thickness, will come back cause the engine isn't in my office there're only in my office and just for H2 two NOS tanks, some NOS exhausts, a NOS gearbox, NOS crankcases and so on
how long time do you need to do them - should be aluminium- when I will give you the thickness?

[downpipe3]

1 week I hope

[Magee]

jp i can get whatever thickness you require mon ami [within reason]
if you let me know what thickness you want i will see what i can do , i can have them made in aluminium if you want

oh yes I want, just have to know the exact thickness, will come back cause the engine isn't in my office there're only in my office and just for H2 two NOS tanks, some NOS exhausts, a NOS gearbox, NOS crankcases and so on
how long time do you need to do them - should be aluminium- when I will give you the thickness?

JP do yorself a favor and dont use ally gaskets, use a thick copper gasket and take any extra off the bottom of your cylinders.
My base gaskets are 3mm thick and worked very well.
I know Gary can get these as well

[mal71]

Why not Ally gaskets Henry ?????

[Magee]

Why not Ally gaskets Henry ?????

i have heard that they can blow out and also deform easy, plus if you use copper you can reuse them by annealing.
Not had any actual experience myself with ally gaskets. I know a few people who use copper and have never had a problem.

But i bet the little house knows on the other board, hey Little Weed !!!

[downpipe3]

either will work henry i have jack up plates on my h2 but i also have copper gaskets either side to obtain my correct deck hieght

[Magee]

either will work henry i have jack up plates on my h2 but i also have copper gaskets either side to obtain my correct deck hieght

dont you mean Jacked up H2 lol

still think copper is better so there

[downpipe3]

true but i dont think you can get copper base gaskets 8mm thick

[husson73]

Gary, need a set in alloy (sorry Henri ) 1.5 minimeter for H2, if you can have them send me the price and I will paypal it